Thinking of remodeling your bathroom? Or are your bathroom light fixtures not working, and you would like to replace them?
If yes, you probably are wondering how exactly you’re going to change the light fixtures of your bathroom safely.
So, this article will take you through the steps on how to remove bathroom light fixture with or without screws.
Table of Contents
- What Tools Will You Need?
- How to Remove Bathroom Light Fixture With Screws
- How to Remove a No-Screw Bathroom Light Fixture
- Spring-Loaded Type of No-Screw Bathroom Light Fixture: How to Remove
- Flush-Mount Type of No-Screw Bathroom Light Fixture: How to Remove
- Notch or Groove Type of No-Screw Bathroom Light Fixture: How to Remove
- Slotted Connectors of No-Screw Bathroom Light Fixture: How to Remove
- Bottom Line
What Tools Will You Need?
Removing bathroom light fixtures is not a hard task if you have the right tools. Let’s have a look at the tools you will need to get the job done.
- Amp meter
How to Remove Bathroom Light Fixture With Screws
Is your bathroom light fixture mounted to the wall or ceiling using screws and nuts? If yes, below is a step-by-step guide on how to remove such fixtures.
Step One: Cut off the Power to your Bathroom
Before you start removing the fixture, you need to disconnect the power to your bathroom first. This way, there will be no danger of electrocuting yourself. You just need to go to the breaker box or fuse box.
Step Two: Remove the Light Fixtures
The second step is to remove the light bulbs that are already fixed in your bathroom. Using your screwdriver, unscrew any nuts and brackets on the fixtures.
Step Three: Check for Voltage
After unscrewing the light bulb from the base, the next thing is to check all the wires for any voltage. You can use an amp meter to do this to confirm if the wires have any electrical voltage.
Step Four: Remove the Wire Nuts
Next, start removing each wire nut at a time. Once you are done with that, you should remove the screws that could be holding the light base to the bathroom wall. And finally, take out the light bulbs from the wall.
How to Remove a No-Screw Bathroom Light Fixture
Removing a light bulb with screws is very easy. But how do you remove one which cannot be unscrewed? Well, it all depends on what type of light fixture you have. So, here are steps on how to remove different types of bathroom light fixtures without screws.
- How to Remove Ceiling Light Fixture with no Screws
- How to Remove Light Fixture Cover with Clips
- How to Remove Glass Dome Light Fixtures
Spring-Loaded Type of No-Screw Bathroom Light Fixture: How to Remove
This type of fixture boasts a tight spring designed to secure the base and dome. To remove the light bulb, you should follow these steps:
Start by inserting a flathead screwdriver between the base of the light bulb and the wall or ceiling. You can also use a knife. Just make sure to be gentle enough, so you don’t damage the ceiling or the fixture base.
Once you have inserted the screwdriver, you should then move it up and down. This is until you can see a gap between the bulb and the wall. The gap should be big enough to fit a finger inside it without struggling.
Next, you will need to disconnect the light bulb from the spring. Simply pull off the bulb with your hands.
Flush-Mount Type of No-Screw Bathroom Light Fixture: How to Remove
For this type of fixture, the base of the light bulb is usually mounted flush with the ceiling. And here is how to remove it:
The first thing to do is to look for the finial, which is the part located at the center of the dome.
After locating the finial, go ahead and loosen it by turning it anticlockwise. Just make sure one hand is holding the dome as you turn the finial.
Once the dome has loosened, you should proceed to dismantle the finial and then remove the light fixture.
Notch or Groove Type of No-Screw Bathroom Light Fixture: How to Remove
This type of fixture has its dome secured safely onto the base via a groove or notch mechanism. To remove this bathroom light fixture, you will need to ask for help from another person. That said, here is how to remove the fixture:
You should press the base towards the wall or ceiling while the other person twists the dome. Twisting the dome helps to detach it from the base. You can then remove the fixture.
Slotted Connectors of No-Screw Bathroom Light Fixture: How to Remove
When it comes to this bathroom light fixture, it usually features raised bumps designed to lock the bulb’s base to the dome. Here is how to remove it:
Twist the dome to detach it from the raised bump.
Pull down the dome but make sure to do it gently, and the light bulb will come out.
As you can see, changing a bathroom light fixture is quite easy. However, removing a non-screw light bulb can seem challenging. But if you know what steps to follow, then you should not have a problem dismantling it.
You just follow the steps above on how to remove bathroom light fixture, and you will be good to go.